Kerfing

Photo

Fri, 13 May 2011 22:29:11 -0400

Photo

Sat, 07 May 2011 22:27:00 -0400

Photo

Mon, 02 May 2011 22:25:00 -0400

Photo

Mon, 02 May 2011 22:20:00 -0400

Photo

Sat, 30 Apr 2011 22:16:00 -0400

Photo

Sat, 30 Apr 2011 22:11:00 -0400

We are now making the steel legs for our little creatures. First...

Wed, 27 Apr 2011 13:27:00 -0400

We are now making the steel legs for our little creatures. First things first, we consulted with Martin in the metal shop. We discussed where we would weld and how we would weld, eventually determining two key things:

1. We need to build a jig.

2. We can puddle weld the legs to the steel plate in order to avoid having a messy connection at the plate.

You might be thinking WTH is a puddle weld. If you are, please refer to this video which explains it pretty well: http://www.youtube.com/watch?v=MHDoll2jqWQ

We have a few concerns about the jig catching on fire if it’s made of plywood so we may have to fabricate it from steel in a different way than shown here. more to come…

Our day began at Rockler woodworking in Somerville where we went...

Sat, 16 Apr 2011 21:44:00 -0400

Our day began at Rockler woodworking in Somerville where we went to pick up some epoxy. We were suffering from sticker shock on even small quantities of the epoxy when Rockler employee, Woody (yes, we’re serious), came around the corner to offer some advice. After some discussion about different methods of filling our kerfed joint, we decided to test out his method of mixing sawdust and wax-free shellac. The advantages of using this method (aside from it being a much cheaper option) is that it should be easy to sand and it will bind to itself in case we need to apply it more than once. We then went back to the shop to test this method and finish our pieces.

The shellac method seemed to work and we left it overnight to dry. The color of the joint was much darker than our nearly white birch ply but it should be okay for our purposes. Unfortunately, the pieces which we had cut with the kerfs a bit shallow were completely unusable, even after we sawed out the excess wood with handsaws. The kerfs would not bend into themselves and so the corner cracked when we tried to fold it together. Also, we realized that although only six kerfs are required geometrically to bend the piece, it may be a good idea to add more to accommodate for cnc error or material variability. We decided to take the opportunity to cut another piece on the CNC and troubleshoot our workflow a bit.

Here were the problems with the last round of cutting:

1. Kerfs were too shallow

2. Kerfs became damaged when the router did a profile cut.

In this test, we addressed this by doing the following:

1. Added an initial step of cutting halfway into the profile cut (.25” depth) in order to “break the edge” before cutting the kerfs.

2. Taped the kerfs down after cutting.

3. Added two kerfs for a total of eight.

4. Because we suspected that an inconsistent maximum z-dimension of the plywood on the CNC bed (due to warping) may have contributed to the shallow kerfing, we ripped the plywood down to a 14” width before CNCing this piece. This enabled the wood to lie flatter (with points screwed down at a lesser distance apart).

The results were much, much better and we were able to fold the piece up immediately. We also had almost no broken kerfs or outside kerf edges. We will need to route the back of this one for the lap joint again before we can fold and glue it into a loop, so that will be our next step.

The CNC left the plywood pieces a bit rough, so we evened out...

Wed, 13 Apr 2011 19:17:09 -0400

The CNC left the plywood pieces a bit rough, so we evened out the edges and pocketed grooves with hand tools. The kerfs were slightly shallow, so we’ve used a hand saw to finish them to the depth needed to bend the piece into a loop. We also routed out the second half of the lap joint that could not be cut on the CNC.

A closer look at the CNC as it mills out the regions into which...

Mon, 11 Apr 2011 14:34:37 -0400

A closer look at the CNC as it mills out the regions into which the steel plate for the legs will be set.

Here’s the CNC mill in progress, using a 1/8” bit to...

Mon, 11 Apr 2011 14:32:57 -0400

Here’s the CNC mill in progress, using a 1/8” bit to cut the kerfs.

Some more photos of the CNC process today.

Mon, 11 Apr 2011 14:21:51 -0400

Some more photos of the CNC process today.

We finally had success cutting out first three pieces of plywood...

Mon, 11 Apr 2011 14:10:13 -0400

We finally had success cutting out first three pieces of plywood for the final pieces. We had minor problems when some of the plywood strips between the kerfs became detached during cutting, but we’re planning to repair those few areas before bending tests. Next we need to route matching depressions for the lap joints on the opposite side of the plywood as the CNC-ed grooves, so that we can bend each piece into a flat, closed loop.

Today was a bit disappointing. We spent a long time wrestling...

Sat, 09 Apr 2011 19:02:00 -0400

Today was a bit disappointing. We spent a long time wrestling with the CNC setup, which turned out to have a controller problem unrelated to our files. When we finally tried to start cutting, we broke a bit. In the end, no pieces were produced today, but we certainly learned a lot about how the CNC does (and does not) work.

Today we practiced our welding technique for the custom steel...

Wed, 06 Apr 2011 13:19:00 -0400

Today we practiced our welding technique for the custom steel legs, with mixed results. The tubing that we used was too thin for the MIG welding, so we’ll probably switch back to solid steel rods for the final legs.

Our first fully folded prototype: it has too many kerfs at each...

Mon, 04 Apr 2011 21:42:00 -0400

Our first fully folded prototype: it has too many kerfs at each bend, but the overall piece folded together quite easily. The epoxy worked well to secure the bonds at the folds, so the next step is to design the CNC files for the final pieces, taking into account our new material thickness and the angles of the folds to design the kerfs correctly.

How to create a plywood loop using 90-degree kerfs and a simple...

Sun, 03 Apr 2011 16:48:00 -0400

How to create a plywood loop using 90-degree kerfs and a simple lap joint.

We used the CNC to cut the first prototype of the plywood loop....

Wed, 30 Mar 2011 17:23:00 -0400

We used the CNC to cut the first prototype of the plywood loop. A central slot and strategically placed kerfs allow the entire piece to be folded from a rectangular flat sheet, with the kerfs facing the interior of the finished loop.

Here’s a video showing the CNC in action, milling the...

Wed, 30 Mar 2011 17:22:00 -0400

Here’s a video showing the CNC in action, milling the kerfs on our plywood sheet.

We built some little sketch models of our creatures, and...

Mon, 28 Mar 2011 16:38:00 -0400

We built some little sketch models of our creatures, and we’re also getting set up to cut the first prototype on the CNC.